Blognya Desnie

Nama   : Mairita Desni
Nim      : 06446/2008
Pend.Teknik Informatika

1. What should a network administrator do first after receiving a call from a user who cannot access the company web server?

* Ask the user what URL has been typed and what error message displays.


2. A customer called the cable company to report that the Internet connection is unstable. After trying several configuration changes, the technician decided to send the customer a new cable modem to try. What troubleshooting technique does this represent?

* Substitution


3. Only one workstation on a particular network cannot reach the Internet. What is the first troubleshooting step if the divide-and-conquer method is being used?

* Check the workstation TCP/IP configuration.


4. Which two troubleshooting techniques are suitable for both home networks and large corporate networks? (Choose two.)

* Documenting the troubleshooting process
* Keeping a record of system upgrades and software versions


5. Identify two physical-layer network problems. (Choose two.)

* hardware failure
* Loose cable connections


6. Which ipconfig command requests IP configuration from a DHCP server?

* Ipconfig /renew


7. What command is used to determine the location of delay for a packet traversing the Internet?

* Tracert


8. What command is used to determine if a DNS server is providing name resolution?

* Nslookup


9. Which troubleshooting method begins by examining cable connections and wiring issues?

* Bottom-up


10. A technician suspects that a Linksys integrated router is the source of a network problem. While troubleshooting, the technician notices a blinking green activity LED on some of the ports. What does this indicate?

* The ports are operational and are receiving traffic.


11. A PC is plugged into a switch and is unable to connect to the network. The UTP cable is suspected. What could be the problem?

* A crossover cable is being used.


12. Refer to the graphic. What configuration is incorrect in the network shown?

13. Which three settings must match on the client and access point for a wireless connection to occur? (Choose three.)

* SSID
* Authentication
* Encryption key


14. A technician is troubleshooting a security breach on a new wireless access point. Which three configuration settings make it easy for hackers to gain access? (Choose three.)

* Configuring NAT
* Broadcasting the SSID
* Using open authentication
* Using the default internal IP address


15. Refer to the graphic. The wireless host cannot access the Internet, but the wired host can. What is the problem?

16. Refer to the graphic. What configuration is incorrect in the network shown?

17. When acting as a DHCP server, what three types of information can an ISR provide to a client? (Choose three.)

* Default gateway
* Dynamic IP address
* DNS server address


18. What two items could be checked to verify connectivity between the router and the ISP? (Choose two.)

* Router status page
* Connectivity status as indicated by LEDs


19. A technician is unsuccessful in establishing a console session between a PC and a Linksys integrated router. Both devices have power, and a cable is connected between them. Which two troubleshooting steps could help to diagnose this problem? (Choose two.)

* Ensure the correct cable is used.
* Ensure the link status LED on the integrated router is lit.


20. Network baselines should be performed in which two situations? (Choose two.)

* After the network is installed and running optimally
* After major changes are implemented on the network


21. Typically, help desk personnel assist end users in which two tasks? (Choose two.)

* Identifying when the problem occurred
* Implementing the solution to the problem


22. How does remote-access software help in the troubleshooting process?

* Diagnostics can be run without a technician being present at the site.


23. Which two items should be added to the documentation following a troubleshooting event? (Choose two.)

* Final resolution
* Results of successful and unsuccessful troubleshooting steps

Nama  : Mairita Desni
NIM   : 06446/2008
Pend.Teknik Informatika


1. Identify three techniques used in social engineering. (Choose three.)
• vishing
• phishing
• pretexting

2. During a pretexting event, how is a target typically contacted?
• by phone

3. While surfing the Internet, a user notices a box claiming a prize has been won. The user opens the box unaware that a program is being installed. An intruder now accesses the computer and retrieves personal information. What type of attack occurred?
• Trojan horse

4. What is a major characteristic of a Worm?
• exploits vulnerabilities with the intent of propagating itself across a network

5. A flood of packets with invalid source-IP addresses requests a connection on the network. The server busily tries to respond, resulting in valid requests being ignored. What type of attack occurred?
• SYN flooding

6. What type of advertising is typically annoying and associated with a specific website that is being visited?
• popups

7. What is a widely distributed approach to marketing on the Internet that advertises to as many individual users as possible via IM or e-mail?
• spam

8. What part of the security policy states what applications and usages are permitted or denied?
• acceptable use

9. Which statement is true regarding anti-virus software?
• Only after a virus is known can an anti-virus update be created for it.

10. Which two statements are true concerning anti-spam software? (Choose two.)
• When anti-spam software is loaded, legitimate e-mail may be classified as spam by mistake.
• Even with anti-spam software installed, users should be careful when opening e-mail attachments.

11. What term is used to describe a dedicated hardware device that provides firewall services?
• appliance-based

12. Which acronym refers to an area of the network that is accessible by both internal, or trusted, as well as external, or untrusted, host devices?
• DMZ

13. Which statement is true about port forwarding within a Linksys integrated router?
• Only external traffic that is destined for specific internal ports is permitted. All other traffic is denied.

14. To which part of the network does the wireless access point part of a Linksys integrated router connect?
• internal

15. Refer to the graphic. What is the purpose of the Internet Filter option of Filter IDENT (Port 113. on the Linksys integrated router?
• to prevent outside intruders from attacking the router through the Internet

16. What statement is true about security configuration on a Linksys integrated router?
• Internet access can be denied for specific days and times.

17. What environment would be best suited for a two-firewall network design?
• a large corporate environment

18. What is one function that is provided by a vulnerability analysis tool?
• It identifies missing security updates on a computer.

19. Many best practices exist for wired and wireless network security. The list below has one item that is not a best practice. Identify the recommendation that is not a best practice for wired and wireless security.
• Disable the wireless network when a vulnerability analysis is being performed.

20. What best practice relates to wireless access point security?
• a change of the default IP address

21. Refer to the graphic. In the Linksys Security menu, what does the SPI Firewall Protection option Enabled provide?
• It requires that packets coming into the router be responses to internal host requests.

Nama : Mairita Desni
NIM  : 06446/2008
Pend.Teknik Informatika


1. Why is IEEE 802.11 wireless technology able to transmit further distances than Bluetooth technology?
• has higher power output

2. What are three advantages of wireless over wired technology? (Choose three.)
• longer range
• easy and inexpensive to install
• ease of adding additional devices

3. What are two benefits of wireless networking over wired networking? (Choose two.)
• mobility
• allows users to share more resources

4. A technician has been asked to provide wireless connectivity to the wired Ethernet network of a building. Which three factors affect the number of access points needed? (Choose three.)
• the size of the building
• the number of solid interior walls in the building
• the presence of microwave ovens in several offices

5. Why is security so important in wireless networks?
• Wireless networks broadcast data over a medium that allows easy access.

6. What does the Wi-Fi logo indicate about a wireless device?
• The device is interoperable with other devices of the same standard that also display   the Wi-Fi logo.

7. Which statement is true concerning wireless bridges?
• connects two networks with a wireless link

8. Which WLAN component is commonly referred to as an STA?
• wireless client

9. Which statement is true concerning an ad-hoc wireless network?
• created by connecting wireless clients in a peer-to-peer network

10. Refer to the graphic. In the Wireless menu option of a Linksys integrated router, what does the Network Mode option Mixed mean?
• The router supports connectivity through infrared and radio frequencies.

11. Refer to the graphic. In the Wireless menu of a Linksys integrated router, what configuration option allows the presence of the access point to be known to nearby clients?
• SSID Broadcast

12. Which two statements about a service set identifier (SSID) are true? (Choose two.)
• tells a wireless device to which WLAN it belongs
• all wireless devices on the same WLAN must have the same SSID

13. Which two statements characterize wireless network security? (Choose two.)
• With SSID broadcast disabled, an attacker must know the SSID to connect.
• Using the default IP address on an access point makes hacking easier.

14. What type of authentication does an access point use by default?
• Open

15. Which statement is true about open authentication when it is enabled on an access point?
• requires no authentication

16. What are two authentication methods that an access point could use? (Choose two.)
• EAP
• pre-shared keys

17. What is the difference between using open authentication and pre-shared keys?
• Pre-shared keys require an encrypted secret word. Open authentication does not require a   secret word.

18. What term describes the encoding of wireless data to prevent intercepted data from being read by a hacker?
• encryption

19. What access-point feature allows a network administrator to define what type of data can enter the wireless network?
• traffic filtering

20. What are the two WEP key lengths? (Choose two.)
• 64 bit
• 128 bit

21. Complete the following sentence: WEP is used to ______ , and EAP is used to _____ wireless networks.
• encrypt; authenticate users on

Nama   : Mairita Desni
NIM    : 06446/2008
Pend.Teknik Informatika


Step 1: Plan the security for your home network
a) 6 Langkah Pengamanan Dasar Jaringan :

1. Ubahlah Sistem ID (Identitas)
Biasanya suatu layanan nirkabel dilengkapi dengan suatu standart pengamanan identitas atau yang sering disebut SSID (Service Set Identifier) or ESSID (Extended Service Set Identifier). Sangat mudah bagi seorang hacker untuk mencari tahu identitas default dari suatu layanan atau jaringan, jadi sebaiknya Anda segera mengubahnya menjadi suatu identitas yang unik, yang tidak mudah ditebak orang lain.
2. Mematikan identitas pemancar
Dengan mengumumkan kepada umum bahwa Anda memiliki suatu jaringan nirkabel akan membuat para hacker penasaran untuk membobol jaringan nirkabel Anda. Mempunyai suatu jaringan nirkabel bukan berarti harus memberitahukannya kepada semua orang. Periksalah secara manual perangkat keras yang Anda pakai untuk jaringan nirkabel tersebut, dan pelajarilah bagaimana cara mematikannya.
3. Sediakanlah enkripsi
WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected Access) dapat meng-enkripsi data Anda sehingga hanya penerima saja yang diharapkan dapat membaca data tersebut. WEP (Wired Equivalent Privacy) mempunyai banyak kelemahan yang membuatnya mudah disusupi. Kunci 128-bit hanya mempunyai tingkat pencapaian yang relatif rendah tanpa peningkatan keamanan yang signifikan, sedangkan untuk 40-bit atau 64-bit pada beberapa perlengkapan lainnya, mempunyai enkripsi yang sama baiknya. Dengan cara pengamanan yang standart saja pastilah tetap akan mudah bagi hacker untuk menyusup, namun dengan cara enkripsi ini pastilah akan membuat jaringan Anda lebih aman dari hacker. Jika memungkinkan, ada baiknya untuk menggunakan enkripsi WPA (peralatan yang lebih tua dapat diupgrade terlebih dahulu agar compatible dengan WPA). WPA dapat sangat menjanjikan dalam menjamin keamanan jaringan nirkabel Anda, namun masih tetap dapat dikalahkan oleh serangan DOS (denial of services).
4. Membatasi dari penggunaan traffic yang tidak perlu
Banyak router jaringan kabel maupun nirkabel yang dilengkapi firewalls. Bukan bermaksud mengedepankan firewalls, namun firewalls telah membantu dalam pertahanan keamanan jaringan. Bacalah petunjuk manual dari perangkat keras Anda dan pelajarilah cara pengaturan konfigurasi router Anda, sehingga hanya traffic yang sudah seijin Anda saja yang dapat dijalankan.
5. Ubahlah 'kata sandi' default Administrator milik Anda
Hal ini baik untuk semua penggunaan perangkat keras maupun perangkat lunak. Kata sandi default sangat mudah disalahgunakan, terutama oleh para hacker. Oleh karena itu sebaiknya ubahlah kata sandi Anda, hindari penggunaan kata dari hal-hal pribadi Anda yang mudah diketahui orang, seperti nama belakang, tanggal lahir, dan sebagainya.
6. Kunci dan lindungilah komputer Anda
Hal ini merupakan cara pengamanan terakhir untuk komputer Anda. Gunakanlah firewall, perangkat lunak Anti Virus, Zone Alarm, dan lain sebagainya. Setidaknya setiap satu minggu perbaharuilah Anti Virus yang Anda pakai.
(dna)

b) Apa resiko akses internet nirkabel

Kita semua tahu bahwa node jaringan nirkabel dapat memancarkan ke kisaran normal sekitar 300 meter, 300 meter, sehingga pemasangan kartu jaringan nirkabel untuk komputer apapun, dapat akses ke node jaringan nirkabel, dan dapat masuk ke jaringan nirkabel, jelas bahwa jenis metode akses mudah, mudah untuk membawa kepada ancaman keamanan jaringan nirkabel. Sebagai contoh, di 300 meter di Taiwan hacker komputer juga memiliki akses ke jaringan nirkabel Anda untuk mengontrol komputer Anda "setiap tindakan"; Walaupun jaringan nirkabel di kurangnya kerahasiaan informasi sebagai ketat kabel jaringan, tetapi Anda tentu tidak ingin serangan melanggar hukum sangat mudah untuk mengetahui keberadaan Anda dalam berbagai jaringan, seperti yang situs yang Anda kunjungi teman-teman, apa yang privasi dari pesan yang dikirim teman-teman di luar negeri, dll, adalah mungkin pengunjung ilegal tahu pasti.

Lebih serius adalah pengunjung ilegal dari jauh setelah Anda masuk ke dalam jaringan nirkabel Anda, akan sangat mudah untuk mencuri semua informasi account online Anda, sehingga akan memberikan keamanan yang lebih besar mengakibatkan kerugian. Jadi ada semua jenis jaringan nirkabel menghadapi risiko keamanan, Anda harus segera mengambil tindakan untuk mengambil tindakan penanggulangan, seperti melalui enkripsi atau verifikasi menggunakan teknologi identifikasi jaringan, untuk memastikan bahwa hanya Anda sebelum ditunjuk pengguna atau peralatan jaringan bisa ke jaringan nirkabel Anda , sementara yang lain ingin memaksa melalui berbagai teknologi jaringan nirkabel untuk mengakses operator jaringan nirkabel Anda, akan ditolak.


Step 8: Reflection
a) LinkSys WRT54G harganya yang murah dan cukup bisa diandalkan.
b) cara untuk membuat jaringan komputer yang aman
Jaringan komputer merupakan kumpulan dari beberapa komputer yang memliki koneksi satu dengan yang lain. Ketika semua komputer saling terhubung dalam suatu jaringan, keamanan merupakan hal yang harus diperhatikan. Fungsi keamanan adalah membuat jaringan komputer menjadi stabil, terstruktur, kuat serta mampu mengatasi berbagai gangguan. Logikanya, bila dalam suatu jaringan komputer ternyata memiliki sisi keamanan yang lemah tentu hal ini berdampak merusak kestabilan jaringan komputer tersebut. Banyaknya gangguan yang masuk akibat lemahnya keamanan yang dibuat bisa merusak kinerja transfer data pada jaringan komputer. Oleh karena itu, gangguan menjadi parameter untuk mengukur tingkat keamanan. Logikanya, sistem tersebut memiliki tingkat keamanan berdasarkan sering tidaknya mengalami gangguan, bukan?

Setelah memahami pentingnya keamanan dalam suatu jaringan maka kita dapat mengkaji lebih detail tentang keamanan jaringan komputer itu sendiri. Prinsip keamanan pada jaringan adalah hal yang sangat kompleks. bahwa keamanan jaringan komputer terdiri dari banyak bagian atau komponen. Sedangkan Tiap komponen itu masih kompleks. Hal ini setidaknya menggambarkan bahwa keamanan jaringan komputer ibarat puzzle yang besar dan rumit. Disamping banyak sekali standar keamanan dalam jaringan komputer, ternyata jumlah dan jenis serangan terhadap keamanan ikut bertambah tiap harinya. Hal ini membuat standar yang sudah dipakai harus dipertimbangkan kembali dan diubah lagi untuk mengimbangi jumlah dan jenis serangan yang selalu bertambah dan bervariasi.

Klasifikasi keamanan menurut David Icove, bahwa 4 tingkat yang harus diperhatikan :
1. Fisik / Physical Security
2. Manusia / Personel Security
3. Data, media , teknik dan komunikasi
4. Kebijakan dan prosedur

Nama   : Mairita Desni
NIM     : 06446/2008
Pend.Teknik Informatika


Step 1: Install the wireless NIC driver
b) NIC untuk Wireless Network
Ada 3 standar yang digunakan, yaitu:
- 802.11a wireless networking
Frekuensi 5 GHz, kecepatan 54 Mbps
Biaya mahal, untuk file-file yang besar
- 802.11b wireless networking
Frekuensi 2,4 GHz, kecepatan 11 Mbps
Interferensi dengan perangkat lain
- 802.11g wireless networking
Frekuensi 2,4 GHz, kecepatan 20 Mbps
Interferensi, throughput lebih dari 802.11b


c) Cara Install Driver Perangkat Lunak Untuk Kartu Lan Nirkabel
Komputer tanpa bekerja antena nirkabel dapat ditingkatkan dengan baik kartu LAN nirkabel internal atau eksternal. Untuk menghubungkan ke hotspot internet favorit Anda atau jaringan rumah,

Anda harus menyelesaikan instalasi dengan menginstal driver perangkat's - file yang memungkinkan perangkat untuk berkomunikasi dengan sistem operasi Anda. Anda dapat memiliki Windows menginstal driver, biarkan Windows memperbarui driver atau manual menginstal driver terbaru sendiri.

http://www.papatek.com/USB-Wireless-LAN-Adapter

Boot komputer Anda. Masukkan disk instalasi driver dan disertakan dengan kartu LAN nirkabel Anda. Klik "Mulai Instalasi," "Instal Perangkat Lunak" atau frase berjudul sama lain.

Ikuti petunjuk pada layar. Mematikan komputer dan memasang kartu ke slot yang tersedia pada motherboard Anda, jika berlaku, kemudian restart komputer. (Beberapa kartu lama seperti

Linksys WMP54G internal 'mengharuskan Anda untuk menginstal perangkat lunak awal sebelum menginstal kartu fisik) instalasi Selesai.. http://www.papatek.com/PCI-Wireless-LAN-Card

Instal Driver Windows Via
Memasang kartu internal Anda. Boot up komputer.

Hubungkan ke Internet setelah beban Windows, kemudian masukkan kartu LAN nirkabel Anda eksternal.

Biarkan Windows kesempatan untuk secara otomatis mendeteksi perangkat Anda dan untuk menginstal driver. Update secara manual Driver

Klik pada "Start" kemudian "Control Panel" klik. Pada "Classic View" pada kolom kiri, jika tersedia.

Buka "System." Klik "Device Manager" pada Windows Vista dan di Windows 7. Klik pada tab "Hardware, kemudian" Device Manager "pada Windows XP.

Double-klik "Network Adapter," kemudian klik dua kali kartu LAN nirkabel Anda diinstal sebelumnya. (Anda harus menginstal Kartu LAN Anda sebelum memperbarui driver, atau tidak terdaftar dalam Device Manager.)

Klik pada Driver "" tab. Klik "Update Driver," lalu "Cari Otomatis" atau "Browse My Computer" jika Anda download driver dari situs web produsen. Ikuti petunjuk pada layar untuk menyelesaikan instalasi driver.

Step 2: Install the wireless NIC

Step 3: Attach to the wireless network
b) SSID copas
d) kekuatan sinyalnya kuat, tidak terbatas
e) ya
g) DHCP
h) membiarkan Windows XP kontrol NIC wireless

Step 4: Determine the NIC driver version

Step 5: Determine if the NIC driver is the most current
a) www.ultimatepcrepair.com
b) Computer Repair - Identifying Home Network Components

Step 6: Verify connectivity
Step 7: Reflection
a) tidak, karena sama saja jaringan nirkabel yang ada di mana saja
b) cukup, karena jangkauan dari AP yang ada di toko makanan tidak cukup luas

Tugas CCNA lab 5.1.4
Oleh: Mairita Desni/06446
Lab 5.1.4 Using the Windows Calculator with Network Addresses
Objectives
• • Switch between the two Windows Calculator modes.
• • Use Windows Calculator to convert between decimal, binary, and hexadecimal.
• • Use Windows Calculator to determine the number of hosts in a network with powers of 2.
Background / Preparation
Network technicians work with binary, decimal, hexadecimal numbers with computers and networking devices. In this lab you will use the Windows Calculator application to convert between the binary, decimal, and hexadecimal number systems. You will also use the powers function to determine the number of hosts that can be addressed based on the number of bits available. The following resources are required:
• • PC with Windows XP installed and functional
Step 1: Access Windows Calculator and determine mode of operation
1. From the Start button menu, select All Programs > Accessories, and click on Calculator. An alternate method of starting the Calculator application is to access the Start menu, click on Run, type calc and press Enter. Try both methods.
2. Once the Calculator application opens, select the View menu option.
3. Which mode [Standard | Scientific] is currently active? Jawab: Mode yang sedang aktif sekarang adalah Scientific
4. Select the Standard mode. This is a basic mode for simple calculations. How many mathematical functions are available in this mode? Jawab: Fungsi matematika yang ada pada Standart model adalah 7 fungsi matematika
Step 2: Convert between number systems
1. Access Scientific mode. Notice the number system modes available—Hex (Hexadecimal), Dec (Decimal), Oct (Octal), and Bin (Binary).
2. Which number system is currently active? Jawab: System bilangan yang sedang aktif pada model Scientific adalah Decimal.
3. Which numbers on the number pad are active in Decimal mode? Jawab: Bilangan yang aktif adalah:
4. Click on the Bin (Binary) mode radio button. Which numbers on the number pad are now active? Jawab:
5. Why do you think the other numbers are grayed out? Jawab: bilangan yang berwarna buram membuktikan bahwa bilangan tersebut tidak aktif untuk binery. Karena bilangan pada binery hanya 0 dan 1.
6. Click on the Hex (Hexadecimal) mode radio button.
7. Which characters on the number pad are now activated? Jawab karakter yang aktif pada bilangan hexadecimal adalah:
8. Click on the Dec radio button. Using your mouse, click on the number 1 followed by the number 5 on the number pad. The decimal number 15 has now been entered. Click on the Bin radio button.
9. What happened to the number 15 listed in the textbox at the top of the window? Jawab: Ketika decimal aktif saya mengetikan angka 15 kemudian saya tukar dengan Binery maka angka 15 berubah menjadi 1111.
10. By selecting different modes, numbers are converted from one number system to another. Select Dec mode again. The number in the window converts back to decimal. Select the Hex mode.
11. Which hexadecimal character (0 through 9 or A through F) represents decimal 15? Jawab: pada Hexadecimal yang mempresentasika 15 adalah F
12. Clear the number 15 in the window. Select Dec mode again. Not only can the mouse be used to enter numbers, but the numerical keypad on the keyboard as well as numbers on the keyboard can also be used. Using the numerical keypad to the right of the ENTER key, type the number 22. Note that if the number does not enter into the calculator, press the Num Lock key to enable the numeric keypad. While the number 22 is showing in the calculator, use the number keys across the top of the keyboard to add a 0 to the number 22 (220 should now be on the calculator). Select the Bin radio button.
13. What is the binary equivalent of 220? Jawab: Decimal 220 equivalent dengan 11011100 pada bineryClear the number 220 in the window. From Binary mode, type in the following binary number: 11001100. Select the Dec radio button.
14. What is the decimal equivalent to the binary number of 11011100? Jawab: Binery 11011100 equivalent dengan 220 Decimal

1. Convert the following decimal numbers to binary.

Decimal Binery
86 1010110
175 10101111
204 11001100
19 10011
1. Convert the following binary numbers to decimal.
Decimal Binery
11000011 195
101010 42
111000 56
10010011 147
Step 3: Convert host IP addresses
1. Computer hosts usually have two addresses, an Internet Protocol (IP) address and an Ethernet Media Access Control (MAC) address. For the benefit of humans, the IP address is normally represented as a dotted decimal notation, such as 135.15.227.68. Each of the decimal octets in the address or a mask can be converted to 8 binary bits. Remember that the computer only understands binary bits. If all 4 octets were converted to binary, how many bits would there be?
Jawab:

jika jumlah semua ada 4 oktet maka ada 32 bit yang terbentuk karena 1 oktet terdiri dari 8 bits.

1. IP addresses are normally shown with four decimal numbers ranging from 0 to 255 and separated by a period. Convert the 4 parts of the IP address 192.168.10.2 to binary.



Decimal Binary
192 11000000
168 10101000
10 00001010
2 00000010s
1. Notice in the previous problem how the 10 converted to only four digits and the number 2 converted to only two digits. When IP addresses can have any number from 0 to 255 in each position, eight digits are normally used to represent each number. In the previous example, eight digits were needed to convert 192 and 168 to binary, but 10 and 2 did not need as many digits. Normally 0s are added to the left of the digits to have eight digits in binary for each IP address number. The number 10 would be shown as 00001010. Four extra zeros are added to the front of the other four binary digits.
2. On the calculator in Binary mode, enter the digits 00001010 and select the Dec radio button.
3. Which decimal number is equivalent to 00001010?
Jawab:

00001010 ekuivalen dengan 10 pada decimal

1. Did adding “leading” zeros affect the number any?
Jawab:

Tidak karena 0 di depan tidak mempunyai pengaruh di dalam pengkonversian.

1. What would the number 2 (in the previous example) be if you were to make it eight digits?
Jawab:

karena pada IP address satu octet harus berisikan 8 digit bilangan biner.

Step 4: Convert host IP subnet masks
1. Subnet masks, such as 255.255.255.0, are also represented as dotted decimal. A subnet mask will always consist of four 8-bit octets, each one represented as a decimal number. With the exception of decimal 0 (all 8 binary zeros) and decimal 255 (all 8 binary ones), each octet will have some number of ones on the left and some number of zeros on the right. Convert the 8 possible decimal subnet octet values to binary.
Decimal Binary
0 00000000.00000000.00000000.00000000
128 11111111.11111111.00000000.00000000
192 11111111.11111111.11111111.00000000
224 11111111.11111111.11111111.00000000
240 11111111.11111111.11111111.00000000
248 11111111.11111111.11111111.00000000
252 11111111.11111111.11111111.00000000
254 11111111.11111111.11111111.00000000
255 11111111.11111111.11111111.11111111
1. Convert the four parts of the subnet mask 255.255.255.0 to binary.
Jawab:

11111111.11111111.11111111.00000000

Step 5: Convert broadcast addresses
1. Computer hosts and network devices use broadcast addresses to send messages to all hosts. Convert the following broadcast addresses.

Address Binery
IP broadcast255.255.255.255 11111111.1111111.11111111.11111111
MAC broadcastFF:FF:FF:FF:FF:FF 11111111.1111111.11111111.11111111
Step 6: Convert IP and MAC addresses for a host
1. Click the Start button, select Run, type cmd, and press Enter. From the command prompt, type ipconfig /all.

1. Make a note of the IP address and physical address (also known as a MAC address).
IP Address:
Jawab:

IP addressnya adalah 192.168.193.71

MAC Address:
Jawab:

MAC addresnya adalah 00-17-C4-23-43-FE

1. Using the calculator, convert the four numbers contained in the IP address to binary.

Decimal Binary
192 11000000
168 10101000
193 11000001
71 01000111
1. The MAC or physical address is normally represented as 12 hexadecimal characters, grouped in pairs and separated by dashes (-). Physical addresses on a Windows-based computer are shown in a format of xx-xx-xx-xx-xx-xx, where each x is a number from 0 to 9 or a letter from a to f. Each of the hex characters in the address can be converted to 4 binary bits which is what the computer understands. If all 12 hex characters were converted to binary, how many bits would there be?
Jawab:

Jika ada 12 karakter hexadecimal maka akan ada 96 bilangan biner yang terbentuk.

1. Convert each of the hexadecimal pairs to binary. For example, if the number CC-12-DE-4A-BD-88-34 was the physical address, convert the hexadecimal number CC to binary (11001100). Then convert the hexadecimal number 12 to binary (00010010) and so on. Be sure to add the leading zeros for a total of 8 binary digits per pair of hex digits.


Hexadecimal Binery
CC 11001100
12 00010010
DE 11011110
4A 01001010
BD 10111101
88 10001000
34 00110100
Step 7: Manipulate powers of 2 to determine the number of hosts on a network
Binary numbers use two digits, 0 and 1. When you calculate how many hosts can be on a subnetwork, you use powers of two because binary is being used. As an example, we have a subnet mask that leaves six bits in the host portion of the IP address. In this case, the number of hosts on that network is 2 to the 6th power minus 2 (because you need a number to represent the network and
1. number that can be used to reach all the hosts—the broadcast address). The number 2 is always used because we are working in binary. The number 6 is the number of bits that are used for the host bits.
2. On the calculator, in Dec mode, input the number 2. Select the x^y key, the key which raises a number to a power. Input the number 6. Click on the = key, press Enter on the keyboard, or press the = key on the keyboard—all give the total. The number 64 appears in the output. To subtract two, click on the minus (-) key and then the 2 key followed by the = key. The number 62 appears in the output. This means 62 hosts could be utilized.
3. Using the previously described process, determine the number of hosts if the following number of bits are used for host bits.

No. of Bits Used forHosts No. of Hosts
5 30 hosts
14 16382 hosts
24 16777214 host
10 1022 hosts
1. Using a similar technique as learned previously, determine what 10 to the 4th power equals.
Jawab:

Hasilnya adalah 9998

1. Close the Windows Calculator application.

Step 8: (Optional) Determine the network number and number of hosts based on subnet mask
1. Given the IP network address of 172.16.203.56 and a subnet mask of 255.255.248.0, determine the network portion of the address and calculate how many hosts can be created from host bits left.
2. Start by converting the 4 octets of the decimal IP address to binary and then convert the decimal subnet mask to binary. Remember to include leading zeros when converting to binary in order to make a total of 8 bits per octet.

Decimal IP addressand subnet mask Binary IP address and subnet mask
172.16.203.56 10101100.00010000.11001011.00111000
255.255.248.0 11111111.11111111.11111000.00000000
1. Align the 32 bits of the subnet mask to the 32 bits of the IP address and compare them. The bits in the IP address that align with the ones bits in the subnet mask represent the network number. What is the binary and decimal network number for this IP address? Determine the binary address first (include all 32 bits) and then convert it to decimal. Binary network address:
Jawab:

10101100.00010000.11001011.00111000
11111111.11111111.11111000.00000000



10101100.00010000.11001000.00000000

Decimal network address:
Jawab:

172.16.200.0
1. How many ones bits are in the subnet mask?
Jawab:

Subnetmask = 2n = 23=8
1. How many bits are left for host bits?
Jawab:

Host = 2n-2= 25-2= 30

1. How many hosts can be created with the bits left?
Jawab:

Host =2n-2= 211-2= 2046

Step 9: Reflection
1. List one other thing for which you might use the Windows Calculator scientific mode. It does not have to be related to networking.

Jawab: Windows Calculator dapat digunkan untuk operasi Matematika dan operasi Gerbang logika.

Tugas CCNA lab 4.2.3
Oleh: Mairita Desni/06446
Lab 4.2.3 Tracing Internet Connectivity
Objectives
• • Use software that shows how data travels through the Internet.
• • Use the ping utility to test connectivity to a remote network.
• • Construct a visual map of connectivity from your network to a remote network.
Background / Preparation
In order to perform this lab, Internet connectivity is required. On a PC, open a web browser to ensure connectivity exists before beginning this lab. This lab has an optional first step of downloading and installing a free program that can be used to determine the path a packet takes through the Internet. This program may be free, but it also may be copyrighted. Also, it may be that you are not permitted on a campus computer to download and install software. Check with the instructor or student assistant if you are unsure. The following resources will be required:
1. • Windows-based computer with Internet connectivity
2. • Ability to download and install freeware software (optional)
3. • Access to the Run command
Step 1: (Optional) Download and install a free program
1. Open a search engine such as Google (www.google.com), Yahoo (www.yahoo.com), or Search (http://search.com).
2. Which words do you think would give you the best result if you are searching for a visual program that allows you to trace how data (a packet) travels through the Internet? Write your search words.Answere: www. google.com
3. Type the words you chose in the Search field. Locate and download the software and install it. Normally, the website has a link to the download site or you can click the words “Download” or “Download Now”. When you download any freeware, remember the location on the hard drive, flash drive, or disk media where you saved the program. Write down where the download is saved. Answere: my Dokuments in folder downloads.
4. What is the name of the program you installed? Answere: IDM (Internet Download Manager)
Step 2: Locate web sites
1. Using the search engine again, locate five businesses with a web server, which are located in a country different from your own.
2. Write the names of the five business web sites. Answere: toko online, bisnis online pilihan, bisnis online indonesia, beton market.
3. Using the search engine again, locate a business in your own country that has a web site that is accessible.
4. Write the URL of the web site. An example URL is www.cisco.com. Answere: www.bisnisonlineindonesia.com
Step 3: (Optional) Use downloaded visual trace route tool
1. Using the software you have downloaded and installed, use the tool to determine the path which the packet takes to reach one of the remote country destinations. Each tool normally allows you to type a URL. The program should either list or visually display the path taken by the packet.
2. How many hops does the packet take to get from your computer to the destination computer? Answere: over a maximum of 30 hops atau lebih dari 30 hops tampak dilayar ada 20 hops(jalur)
3. If your tool also provides time information, write down how long it took for the packet to reach the first hop? Answere:15 menit
4. Use the tool to determine the path to another foreign country site.
5. How many hops does the packet take to get from your computer to the destination computer? Answere: http://www.netlink.co.uk/users/itcentre/ lebih dari 30 hop(jalur yang dilintasinya) namun terlihat dilayar ada 17 hop yang dilalui.
6. Use the tool to determine the path to a web site in your own country. Yaitu: www.pemdapadang.com ada 30 hops.Was the time it took to reach a web site in your own country shorter or longer? Answere: longer
7. Try to think of an instance where the time it takes to reach a web server in your own country would be longer than it takes to reach another country’s web server? Answere: karena di Indonesia belum ada server yang besar sehingga pengiriman paket data harus melalui server Negara lain.
Step 4: Use the tracert command
1. Click the Start button, click the Run option, type cmd, and press Enter. An alternate way to get to the command prompt is to click Start > All Programs > Accessories > Command Prompt.
2. From the command prompt, type tracert and press Enter. Options that can be used with the tracert command are shown. Items shown in square brackets [ ] are optional. For example, the first option that can be used with the tracert command is –d. If someone was to type tracert –d www.cisco.com, then the command issued to the computer is to trace the route to www.cisco.com, but do not try to resolve IP addresses to names. The target_name parameter is mandatory (it does not have brackets around it) and it is replaced with the destination network. In the previous example of tracert –d www.cisco.com, www.cisco.com is the target_name.
3. Which tracert option would be used to designate that only 5 hops could be used to search for the device address on the destination network? Jawaban: 10.10.14.45, 172.20.11.82, 222.124.3.9, 203.208.131.89 dan 59.128.15.141
4. Write the full command that would be typed to trace a route to www.cisco.com and instruct the computer to not search for it after seven hops. Jawaban: tracert –d www.cisco.com
5. Using one of the remote country destination addresses (use the same address as the one you used with the visual tool if possible) use the tracert command to determine how many hops it takes to reach the remote web server. Write the number of hops and the destination. Jawaban:
6. The tracert command uses Internet Control Message Protocol (ICMP) echo request messages to determine the path to the final destination. The path displayed is a list of IP addresses assigned to routers that connect to one another to form the path. The ICMP packets contain a value called a Time To Live (TTL). The TTL value is 30 by default on a Microsoft-based PC and each router through which the packet passes, decrements that value by 1 before sending the packet on to the next router in the path. When the TTL value reaches 0, the router that has the packet sends an ICMP time exceeded message back to the source. The tracert command determines the path by sending the first ICMP echo request message with a TTL of 1 and then increases that TTL value by 1 until the target responds or the maximum number of hops is reached. The path is determined by examining the ICMP time exceed messages that are sent back by routers along the way and by the ICMP echo reply message that is returned from the destination. Routers that do not return the ICMP time exceed messages are shown by a row of asterisks (*).
7. How many hops does your tracert command show that the packet went through? Jawaban:
Step 5: Use the pathping command
1. A similar command that can be used on a Windows XP computer is pathping. This command combines the abilities of the tracert command with the ping command. From the command prompt, use the pathping command to determine the IP addresses of the routers used to create the packet path to another foreign country address. An example of the pathping command used to trace the path to Cisco is pathping www.cisco.com. Jawaban:
2. How many hops did the pathping command display to your remote destination? When do you think that you would ever use a tool like pathping or tracert?
Step 6: (Optional) Use the whois function
1. Some of the freeware tools include an option to perform a whois function. Whois is a separate program or integrated with a tool similar to tracert or pathping. It displays (and sometimes has a link) who owns the web link of either the destination URL (such as cisco.com) or any of the links along the path. Explore the freeware tool that you have downloaded and installed and determine if it has a whois function. If it does, use it to determine who owns the domain name of one of the previous destinations used.
2. Why would you want to use the whois function? Jawaban:
Step 7: Reflection
With a classmate, compare all of the commands used in this lab. Describe the purpose and benefit of each one. Which do you think is the most useful command? Jawaban:

Tugas CCNA lab 3.3.3
Oleh: Mairita Desni/06446
Lab 3.3.3 Determine the MAC Address of a Host
Objective
• Determine the MAC address of a Windows XP computer on an Ethernet network using the ipconfig /all command.
• Access to the Run command.
Background/Preparation
Every computer on an Ethernet local network has a Media Access Control (MAC) address that is burned into the Network Interface Card (NIC). Computer MAC addresses are usually displayed as 6 sets of two hexadecimal numbers separated by dashes or colons. (example: 15-EF-A3-45-9B-57). The ipconfig /all command displays the computer MAC address. You may work individually or in teams. The following resources are required:
• • Windows XP workstation with at least one Ethernet network interface card (NIC)
Step 1: Open a Windows command prompt window
• From the Windows XP desktop, click Start then Run.
• Type cmd in the Run dialogue box then click OK.A Windows command prompt window opens.
Step 2: Use the ipconfig /all command
a. Enter the ipconfig /all command at the command prompt.
b. Press Enter. (Typical results are shown in the following figure, but your computer will display different information.)
Step 3: Locate the MAC
in the output from the ipconfig /all command
a. Use the table below to fill in the description of the Ethernet adapter and the Physical (MAC) Address:
Description Physical Address(es)
WAN Interface 00-53-45-00-00-00
Step 4: Reflection
a. Why might a computer have more than one mac address? Jawaban: karena mac memiliki pengaturan sendiri yang diberikan secara otomatis kepada koputer.
b. The sample output from the ipconfig /all command shown previously had only one MAC address. Suppose the output was from a computer that also had wireless Ethernet capability. How might the output change? Jawaban: perubahan ini dapat dilakukan secara otomatis saat PC tekkoneksi.
c. Try disconnecting the cable(s) to your network adapter(s) and use the ipconfig /all command again. What changes do you see? Does the MAC address still display? Will the MAC address ever change? Jawaban: ya. Perubahan pada mac dan IP addressnya.
d. What are other names for the MAC address? Jawaban: 192.168.245.199

Tugas CCNA lab 3.1.5
Oleh Mairita Desni /06446
Lab 3.1.5 Building a Peer-to-Peer Network
Objectives
• • Design and build a simple peer-to-peer network using a crossover cable supplied by the instructor.
• • Verify connectivity between the peers using the ping command.
Background / Preparation
In this hands-on lab, you will plan and build a simple peer-to-peer network using two PCs and an Ethernet crossover cable. The following resources are required:
• • Two Window XP Professional PCs, each with an installed and functional Network Interface Card (NIC)
• • An Ethernet crossover cable
Step 1: Diagram the network
1. A network diagram is a map of the logical topology of the network. In the space below, sketch a simple peer-to-peer network connecting two PCs. Label one PC with IP address 192.168.1.1 and the other PC with IP address 192.168.1.2. Use labels to indicate connecting media and any necessary network devices.


Answere:
1. A simple network like the one you designed can use a hub or switch as a central connecting device, or the PCs may be directly connected. Which kind of cable is required for a direct Ethernet connection between the two PCs? Answere: Straight-through Cables
Step 2: Document the PCs
1. Check the computer name settings for each PC and make adjustments as necessary. For each PC, select Start and Control Panel. Double-click the System icon, then click the Computer Name tab. Write down the computer name that is displayed following Full computer name:
PC1 Name Computer 1
PC2 Name Computer 2
1. Check to see if the two PCs have the same name. If they do, change the name of one PC by clicking the Change button, typing a new name in the Computer name field, then clicking OK.
2. Click OK to close the System Properties window.
3. Why is it important that each PC on a network have a unique name? Answere: because if there are the same name of computer make the failed connections, and this is the rules of connections.
Step 3: Connect the Ethernet cable
1. Use the Ethernet crossover cable provided by the instructor. Plug one end of the cable into the Ethernet NIC of PC1.
2. Plug the other end of the cable into the Ethernet NIC of PC2. As you insert the cable, you should hear a click which indicates that the cable connector is properly inserted into the port.
Step 4: Verify physical connectivity
1. After the Ethernet crossover cable is connected to both PCs, take a close look at each Ethernet port. A light (usually green or amber) indicates that physical connectivity has been established between the two NICs. Try unplugging the cable from one PC then reconnecting it to verify that the light goes off then back on.
2. Go to the Control Panel, double click the Network Connections icon, and confirm that the local area connection is established. The following figure shows an active local area connection. If physical connectivity problems exist, you will see a red X over the Local Area Connection icon with the words Network cable unplugged.
3. If the Local Area Connection does not indicate that it is connected, troubleshoot by repeating Steps 3 and 4. You may also want to ask your instructor to confirm that you are using an Ethernet crossover cable.
Step 5: Configure IP settings
1. Configure the logical addresses for the two PCs so that they are able to communicate using TCP/IP. On one of the PCs, go to the Control Panel, double click the Network Connections icon, and then right click the connected Local Area Connection icon. Choose Properties from the pull-down menu.
2. Using the scroll bar in the Local Area Connection Properties window, scroll down to highlight Internet Protocol (TCP/IP). Click the Properties button.
3. Select the Use the following IP address radio button and enter the following information:
IP Address 192.168.1.1 Kelas C
Subnet Mask 255.255.255.0 Subnet mask default kelas C
1. Click OK, which will close the Internet Protocol (TCP/IP) Properties window. Click the Close button to exit the Local Area Connection Properties window.
2. Repeat steps 5a – 5d for the second PC using the following information:
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
Step 6: Verify IP connectivity between the two PCs
NOTE: To test TCP/IP connectivity between the PCs, Windows Firewall must be disabled temporarily on both PCs. Windows Firewall should be re-enabled after the tests have been completed.
1. On PC1, on the Windows XP desktop, click Start. From the Start menu, select Control Panel, and double-click Network Connections.
2. Right-click the Local Area Connection icon and select Properties. Click the Advanced tab. Locate and click the Settings button.
3. Make a note of whether the firewall settings are ENABLED (ON) for the Ethernet port or DISABLED (OFF) for the Ethernet port.
4. If the firewall settings are enabled, click the Off (not recommended) radio button to disable thefirewall. The setting will be re-enabled in a later step. Click OK in this dialog box and the following to apply this setting.
5. Now that the two PCs are physically connected and configured correctly with IP addresses, we need to make sure they communicate with each other. The ping command is a simple way to accomplish this task. The ping command is included with the Windows XP operating system.
6. On PC1, go to Start, then Run. Type cmd, and then click OK. A Windows command prompt window will appear as shown in the figure below.
7. At the > prompt, type ping 192.168.1.2 and press Enter. A successful ping will verify the IP connectivity. It should produce results similar to those shown in here.
8. Repeat Steps 6a-6c on the second PC. The second PC will ping 192.168.1.1.
9. Close the Windows command prompt window on both PCs.
Step 7: Verify connectivity using My Network Places
1. A PC can share its resources with other PCs on the network. PCs with shared resources should be visible through My Network Places. On PC1, go to Start, click My Network Places, and then click View workgroup computers in the left panel.
2. Do you see an icon for the other PC in your peer-to-peer network? Answere: yes, I do.
3. What is the name of the other PC? Answere: à Cisco 27 and Cisco 28.
4. Is it the same name you recorded in Step 2? Answere: No, it is.
5. Perform Step 7a on the second PC.
6. Close any open windows.
Step 8: (Optional – Use only if the Firewall was originally ENABLED) Re-enable the firewall
1. If you disabled the Windows Firewall in Step 6, click Start, select Control Panel, and open the Network Connections control panel.
2. Right-click the Ethernet network connection icon and select Properties. Click the Advanced tab. Locate and click Settings.
3. If the firewall settings are disabled (and they were enabled before this lab began), click the On radio

• Determine the current screen resolution of a PC monitor.
• Determine the maximum resolution for the highest color quality.
• Calculate the number of pixels needed for resolution settings.
• Identify the type of monitor and graphics card installed.

• • Capability of the monitor
• • Capability of the graphics card, especially the amount of onboard memory

• • Computer with Windows XP installed

1. To view the current screen resolution and color quality settings, right-click on any empty space on the desktop and select Properties from the context menu. In the Display Properties window, select the Settings tab.
2. You can also access Display Properties by opening the Control Panel and clicking the Display icon.
3. Use the Display Properties Settings tab to record the current settings on your PC: The screen resolution is (H by V) Answere: Horizontal The horizontal resolution is: 1024, The vertical resolution is: 768, The color quality value is: 32 bit

1. The display on the screen consists of rows of pixels. The number of pixels in each row is the horizontal resolution. The number of rows is the vertical resolution. To determine the total number of pixels in a screen resolution, you multiply the horizontal resolution by the vertical resolution. For example, if the current resolution is 1280 x 1024, the total number of pixels is 1280 times 1024, or 1,310,720. Answere:
2. Calculate the total number of pixels for the lowest resolution: 600 pixels______________________
3. Calculate the total number of pixels for the maximum resolution: 1280 pixels____________________

1. Use the information found in the Adapter tab to complete the following table:

Graphics card manufacturer and model (Adapter Type)Graphics memory on card (Memory Size)

Chip type, DAC Type, memory Size, adapter string, Bios infoemation128 MB, but this is based on speck of the each of the computer.

1. Click on the Monitor tab to see the monitor type and current refresh rate.
2. Use the information found in the Monitor tab to complete the following table: Answere:

Monitor type	Plug and Play Monitor and NVIDIA GeForce Go 7400
Supported refresh rates	60 Hert